Skip to content

oddWires Proteus

The oddWires Proteus is one of the development board created by oddWires to evaluate the ESP-WROOM-32 module. It is based on the ESP32 microcontroller that boasts Wifi, Bluetooth, Ethernet and Low Power support all in a single chip.

The Proteus offers a 240 MHz, 32-bit processor with 4Mb of flash memory. The Proteus accepts all of the IoT-Bus modules and is also a version with a large prototyping area which enables a single-board IoT solution. This version includes both 3.3V and 5V power rails

The oddWires IoT-Bus System is based on a low-cost, open design that includes multiple main boards including a minimalist, breadboard-friendly form factor.

Pin Mapping

Official reference for oddWires Proteus can be found here.

Flash Layout

The internal flash of the ESP32 module is organized in a single flash area with pages of 4096 bytes each. The flash starts at address 0x00000, but many areas are reserved for Esp32 IDF SDK and Zerynth VM. There exist two different layouts based on the presence of BLE support.

In particular, for non-BLE VMs:

Start address Size Content
0x00009000 16Kb Esp32 NVS area
0x0000D000 8Kb Esp32 OTA data
0x0000F000 4Kb Esp32 PHY data
0x00010000 1Mb Zerynth VM
0x00110000 1Mb Zerynth VM (FOTA)
0x00210000 512Kb Zerynth Bytecode
0x00290000 512Kb Zerynth Bytecode (FOTA)
0x00310000 512Kb Free for user storage
0x00390000 448Kb Reserved

For BLE VMs:

Start address Size Content
0x00009000 16Kb Esp32 NVS area
0x0000D000 8Kb Esp32 OTA data
0x0000F000 4Kb Esp32 PHY data
0x00010000 1216Kb Zerynth VM
0x00140000 1216Kb Zerynth VM (FOTA)
0x00270000 320Kb Zerynth Bytecode
0x002C0000 320Kb Zerynth Bytecode (FOTA)
0x00310000 512Kb Free for user storage
0x00390000 448Kb Reserved

Device Summary

  • Microcontroller: Tensilica 32-bit Single-/Dual-core CPU Xtensa LX6
  • Operating Voltage: 3.3V
  • Input Voltage: 7-12V
  • Digital I/O Pins (DIO): 26
  • Analog Input Pins (ADC): 16
  • Analog Outputs Pins (DAC): 2
  • UARTs: 3
  • SPIs: 2
  • I2Cs: 3
  • Flash Memory: 4 MB
  • SRAM: 520 KB
  • Clock Speed: 240 Mhz
  • Wi-Fi: IEEE 802.11 b/g/n/e/i:
    • Integrated TR switch, balun, LNA, power amplifier and matching network
    • WEP or WPA/WPA2 authentication, or open networks

Power

Power to the oddWires Proteus is supplied via the on-board USB Micro B connector or directly throught the connector for a 3.7/4.2 V battery. The power source is selected automatically.

The device can operate on an external supply of 2.5 to 6 volts. If using more than 6V, the voltage regulator may overheat and damage the device.

Connect, Register, Virtualize and Program

The oddWires Proteus comes with a serial-to-usb chip on board that allows programming and opening the UART of the ESP32 module. Drivers may be needed depending on your system (Mac or Windows) and can be download from the official Espressif documentation page. In Linux systems, the oddWires Proteus should work out of the box.

Note

For Linux Platform: to allow the access to serial ports the user needs read/write access to the serial device file. Adding the user to the group, that owns this file, gives the required read/write access: Ubuntu` distribution –> dialout group; Arch Linux distribution –> uucp group.

Once connected on a USB port, if drivers have been correctly installed, the oddWires Proteus device is recognized by Zerynth Studio. The next steps are:

  • Select the oddWires Proteus on the Device Management Toolbar (disambiguate if necessary);
  • Register the device by clicking the “Z” button from the Zerynth Studio;
  • Create a Virtual Machine for the device by clicking the “Z” button for the second time;
  • Virtualize the device by clicking the “Z” button for the third time.

Note

No user intervention on the device is required for registration and virtualization process.

After virtualization, the oddWires Proteus is ready to be programmed and the Zerynth scripts uploaded. Just Select the virtualized device from the “Device Management Toolbar” and click the dedicated “upload” button of Zerynth Studio.

Note

No user intervention on the device is required for the uplink process.

Firmware Over the Air update (FOTA)

The Firmware Over the Air feature allows to update the device firmware at runtime. Zerynth FOTA in the oddWires Proteus device is available for bytecode and VM.

Flash Layout is shown in table below:

Start address Size Content
0x00010000 1Mb Zerynth VM (slot 0)
0x00110000 1Mb Zerynth VM (slot 1)
0x00210000 512Kb Zerynth Bytecode (slot 0)
0x00290000 512Kb Zerynth Bytecode (slot 1)

For BLE VMs:

Start address Size Content
0x00010000 1216Kb Zerynth VM (slot 0)
0x00140000 1216Kb Zerynth VM (slot 1)
0x00270000 320Kb Zerynth Bytecode (slot 0)
0x002C0000 320Kb Zerynth Bytecode (slot 1)

For Esp32 based devices, the FOTA process is implemented mostly by using the provided system calls in the IDF framework. The selection of the next VM to be run is therefore a duty of the Espressif bootloader; the bootloader however, does not provide a failsafe mechanism to revert to the previous VM in case the currently selected one fails to start. At the moment this lack of a safety feature can not be circumvented, unless by changing the bootloader. As soon as Espressif relases a new IDF with such feature, we will release updated VMs.

Secure Firmware

Secure Firmware feature allows to detect and recover from malfunctions and, when supported, to protect the running firmware (e.g. disabling the external access to flash or assigning protected RAM memory to critical parts of the system).

This feature is strongly platform dependent; more information at Secure Firmware - ESP32 section.

zerynth secure socket

To be able to use zerynth secure socket on esp32 boards native_mbedtls: true must be used instead of zerynth_ssl: true in the project.yml file.

Missing features

Not all IDF features have been included in the Esp32 based VMs. In particular the following are missing but will be added in the near future:

  • Touch detection support